Can you put an epoxy flake floor over a plywood subfloor? Yes. STAUF USA, the coatings maker we distribute in Hawaii, has a method it has used on multiple plywood floors: bare, untreated plywood, EFP-290 in the screw holes and seams, EHS-265 primer, then ULC-500 LevelSeal instead of an epoxy base coat, flakes, and a CCO-651 top coat. Below are the steps, the reason for each product, and a priced materials list for a 400 sq ft floor.

Price your floor in 1 minute →
In the calculator, choose "Bare plywood / wood subfloor".

Can you put epoxy on a plywood floor?

You can, with the right system. We asked STAUF's coatings director about a customer's 400 sq ft wood floor. Her answer: "You can absolutely do a system over a plywood substrate." STAUF has done multiple plywood floors this way, including job trailers and food trailers, where the floor flexes more than in a house because the trailer moves on the road. STAUF reports those floors are all working as expected.

The catch is the word bare. The method below is for untreated plywood with no coating on it. It is not a method for a finished hardwood floor (see the warning further down).

Why ULC-500 instead of epoxy over plywood

Over concrete, STAUF's flake floor uses CCI-610 epoxy as the base coat. Epoxy dries rock hard, which is great on a slab. Plywood flexes more than concrete, so over plywood STAUF switches the base coat to ULC-500 LevelSeal, which has more give. Everything else in the system stays STAUF: the primer, the flakes and the top coat.

ULC-500 is tan. Under gray flakes, STAUF tints it with one 2 fl oz bottle of XCF ColorFast #11 Fog per ULC-500 kit, so small gaps between flakes don't show a tan base.

Who this fits

  • A room, addition or loft with a plywood subfloor that you want to finish as a flake floor.
  • Job trailers and food trailers: STAUF has applied this system in both.

Concrete slab instead? See how to epoxy a garage floor. Existing tile? See epoxy flake floor over existing tile.

Before you start: the plywood must be bare

  • Untreated plywood, no coating. No paint, sealer or finish of any kind.
  • Sand off raised areas so the surface is flat.
  • Finished hardwood floor? STAUF's coatings director has not put this system over a hardwood floor. Her main concern: the finish on that floor would need to be removed first. Call or text us at (808) 210-4807 before you plan a job like that.

Step by step: STAUF's flake floor over plywood

  1. Prep. Make sure the plywood is untreated and uncoated. Sand to remove raised areas, then clean off the dust.
    Step 1: bare, untreated plywood is sanded flat 1Sand the bare plywoodbare plywood subfloorsand raised areas,then remove the dust
    Untreated, uncoated plywood only. Sand off raised areas and remove the dust.
  2. Fill screw holes and seams with EFP-290. Use STAUF EFP-290 Epoxy Floor Patch in every screw hole and seam, and let it dry.
    Step 2: EFP-290 patch fills the screw holes and seams in the plywood 2EFP-290 in holes and seamsbare plywood subfloorfill cracks, holes,seams flush
    Fill every screw hole and seam with EFP-290 and let it dry.
  3. Prime with EHS-265. STAUF EHS-265 Hydro-Seal is a water-based epoxy primer. On plywood it may take 2 primer coats.
    Step 3: a roller applies EHS-265 primer over the plywood 3Prime with EHS-265bare plywood subfloorroll, then cross-rollEHS-265 primer
    Up to 2 primer coats on plywood.
  4. Spread the ULC-500 base coat. Mix ULC-500 LevelSeal with its tint and spread it with the #10 trowel blade. Then backroll with the blue texture roller to release bubbles.
    Step 4: tinted ULC-500 is spread with the #10 trowel blade over the primed plywood 4Tinted ULC-500 base coatbare plywood subfloornotched trowelULC-500 body coat (tinted)
    ULC-500 has more give than epoxy, so it suits plywood. Backroll to release bubbles.
  5. Broadcast the flakes. Broadcast STAUF XPF polymer flakes into the wet ULC-500 and let it dry for 4–6 hours.
    Step 5: flakes are broadcast into the wet ULC-500 5Broadcast the flakesbare plywood subfloorbroadcast flakesby hand, full coverXPF flakes
    Full broadcast into the wet ULC-500, then 4–6 hours to dry.
  6. Scrape, vacuum, top coat. Scrape off loose flakes, vacuum, and apply the CCO-651 polyurethane top coat.
    Step 6: loose flakes are scraped off and the CCO-651 top coat is rolled on 6Scrape, vacuum, CCO-651bare plywood subfloorscrape loose flakes,vacuum, then top coatCCO-651 top coat
    CCO-651 seals the flakes for the finished floor.
Cross-section of STAUF's flake floor over plywood: plywood with EFP-290, EHS-265, tinted ULC-500, XPF flakes, CCO-651 top (you walk here)CCO-651 top coatXPF flakes, full broadcastULC-500, tinted #11 FogEHS-265 primer (up to 2 coats)Bare plywood, EFP-290 in seamsbottom
From the plywood up: the same flakes and top coat as on concrete, with ULC-500 in place of the epoxy body coat.

The STAUF coatings here are two-part products. Read each product's data sheet for mixing, working time, and the temperature and humidity range before you schedule the job, especially inside a closed trailer on a hot day.

What you need for a 400 sq ft plywood floor

These are the quantities our epoxy floor calculator plans for 400 sq ft over bare plywood, with our prices on 17 Nov 2026. We add about 10% extra, as STAUF recommends, then round each product up to whole kits.

Product Qty Total
EFP-290 Epoxy Floor Patch kit (amount depends on the seams) 1 $117.12
EHS-265 primer, 2.5-gal kit (2 coats) 2 $684.84
ULC-500 LevelSeal kit (100 sq ft per kit) 5 $836.10
XCF #11 Fog tint, 2 fl oz (1 per ULC-500 kit) 5 $185.40
XPF flakes, 25-lb box (200 sq ft per box) 3 $441.42
CCO-651 top coat, 2-gal kit (480 sq ft per kit) 1 $660.00
Subtotal $2,924.88
Hawaii GET 4.712% $137.82
Total $3,062.70

Prices change. The calculator always uses today's prices, and you can send the result to us for a confirmed quote.

What the finished floor looks like

Gray STAUF epoxy flake floor before and after in a two-car garage
A gray STAUF flake floor, before and after. This one is over a concrete garage slab; it shows the flake look and is not a plywood job. Project photo: STAUF USA, not a Best Flooring Honolulu install.

Which STAUF product goes where

Follow each floor in order, 1 to 7: that is the order you apply them. Same color = same product.

1Patch
2Primer
3Body / color coat
4Tint
5Decoration
6Top coat
7Final coat
Garageconcrete
1 PatchEFP-290Epoxy floor patchcracks, holes, spalls
2 PrimerEHS-265Epoxy primer800 sq ft / kit
3 Body / color coatCCI-610Epoxy body coat500 sq ft / kit
4 TintXCF #11 FogGray tint32 oz per CCI kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Commercial kitchenconcrete
1 PatchEFP-290Epoxy floor patchcracks, holes, spalls
2 PrimerEHS-265Epoxy primer800 sq ft / kit
3 Body / color coatULC-500LevelSeal body coat100 sq ft / kit
4 TintXCF #11 FogGray tint2 oz per ULC kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Bathroom / any tileexisting tile
1 PatchEFP-290Epoxy floor patchbroken tiles
2 PrimerERP-270 + sandPrimer + moisture barrier175 sq ft / kit
3 Body / color coatULC-500LevelSeal body coat100 sq ft / kit
4 TintXCF #11 FogGray tint2 oz per ULC kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Plywoodbare subfloor
1 PatchEFP-290Epoxy floor patchscrew holes, seams
2 PrimerEHS-265 × 2Epoxy primer, 2 coats800 sq ft / kit per coat
3 Body / color coatULC-500LevelSeal body coat100 sq ft / kit
4 TintXCF #11 FogGray tint2 oz per ULC kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Metallicconcrete
1 PatchEFP-290Epoxy floor patchcracks, holes, spalls
2 PrimerEHS-265Epoxy primer800 sq ft / kit
3 Body / color coatERP-270Base coat, #10 trowel175 sq ft / kit
4 TintXCF Jet (black), 32 ozBase tint, special order (STAUF 1st choice)1 per ERP kit
5 DecorationCCI-610 + pigmentMetallic coat (pigment: special order)125 sq ft / kit + 12 oz pigment per kit
6 Top coatno flakes,
no CCO-651
7 Final coatUPS-670 / 675Gloss / matte, the only top coatup to 400 sq ft/gal
  1. 1Tile → ERP-270 primer. Everything else → EHS-265.
  2. 2Rigid concrete garage → CCI-610 body coat. Anything that moves, or a kitchen (tile, plywood, kitchen slab) → ULC-500.
  3. 3Every flake floor → XPF flakes + CCO-651.
  4. 4UPS-670 / UPS-675 = optional last coat on flake floors, for a smoother finish. On metallic it is the only top coat.

* Flake floors: UPS-670/675 is optional. STAUF (20 Nov 2026): one CCO-651 coat gives a shiny, textured floor; add UPS for a smoother finish. Coverage is approximate, per kit or box, before the ~10% extra our calculator adds. EFP-290: as much as the repairs need. Kit sizes: EHS-265, ERP-270, CCI-610 2.5 gal; CCO-651 2 gal; XPF 25-lb box. Sources: STAUF USA (system recipes, coatings director's rates), STAUF data sheets and the DCS metallic guide. Best Flooring Honolulu, 20 Nov 2026.

The rest of the series

Where to get the materials on Oahu

Best Flooring Honolulu is STAUF's exclusive distributor in Hawaii. Pick up the STAUF flake-floor products at our Waipio warehouse, or we ship to all islands. See every STAUF product and the full epoxy flooring collection. Questions about your floor? Call or text (808) 210-4807.

FAQ: epoxy over a plywood subfloor

Can you put epoxy over a finished hardwood floor?

STAUF's coatings director has not put this system over a hardwood floor. Her main concern is that the floor's finish would need to be removed first. Call or text (808) 210-4807 before planning it.

Why not use a regular epoxy base coat over plywood?

Epoxy dries rock hard, and plywood flexes more than concrete. STAUF uses ULC-500 LevelSeal over plywood because it has more give.

How many primer coats does plywood need?

Plan on up to 2 coats of STAUF EHS-265. Our calculator plans 2 coats at 800 sq ft per 2.5-gal kit per coat, plus about 10% extra: 2 kits for a 400 sq ft floor.

Can I put a flake floor in a food truck or job trailer?

Yes. STAUF has applied this plywood system in multiple job and food trailers. They move on the road, so the floor flexes more than in a house, and STAUF reports they are all working as expected.

How much ULC-500 do I need?

One ULC-500 kit per 100 sq ft, plus one 2 fl oz XCF tint per kit. Our calculator adds about 10% extra, as STAUF recommends, so a 400 sq ft floor needs 5 kits and 5 tints.

November 17, 2026 — Best Flooring Honolulu

Leave a comment

Please note: comments must be approved before they are published.