How do you epoxy a garage floor? On bare concrete, STAUF USA's flake system is four layers: EHS-265 primer, a CCI-610 body coat tinted gray, a full broadcast of XPF flakes, and a CCO-651 top coat. This guide walks you through it one step at a time, with a drawing for each step, and a priced list for a 400 sq ft garage. Commercial kitchen? There is a branch for that below.

Price your floor in 1 minute →
In the calculator, choose "Bare concrete".

Garage floor before and after a STAUF epoxy flake coating
A garage before and after a STAUF flake floor. Project photo: STAUF USA, not a Best Flooring Honolulu install.

What you need

Step by step: how to epoxy a concrete garage floor

  1. Prep the slab. Tape off the walls at floor level. Grind the concrete to remove paint, drywall mud and other contaminants. You don't need an aggressive grind, just a clean, porous surface. Vacuum, then sprinkle a few drops of water: if they soak in within 60 seconds, the slab is ready. If not, grind a little more. Then fill cracks, holes and spalls flush with EFP-290 (it dries in about four hours). Source: STAUF DCS installation guide, concrete prep.
    Step 1: a grinder cleans the concrete slab; a water drop soaks in within 60 seconds 1Prep the slabconcrete slabwater drop soaksin within 60 s
    Grind until a water drop soaks in within 60 seconds. Fill cracks and spalls with EFP-290.
  2. Prime with EHS-265. Mix part A and part B for 3 minutes; it turns milky white. Cut in the edges with a brush and mini roller, then roll and cross-roll the floor in sections of about 5 × 5 ft, cutting in as you go to keep a wet edge. The primer dries clear. Let it dry completely before the next coat. STAUF's reason: the primer soaks partly into the porous concrete and locks down, so the colored coat stays on top instead of soaking in.
    Step 2: a roller applies a thin EHS-265 primer coat over the slab 2Prime with EHS-265concrete slabroll, then cross-rollEHS-265 primer
    Roll and cross-roll in 5 × 5 ft sections. Milky white when wet, clear when dry.
  3. Apply the tinted body coat. Mix one 32 fl oz bottle of XCF #11 Fog into each 2.5-gal kit of CCI-610 and apply it over the dry primer. The tint is always used: it shows you that every spot is covered, and it hides the specks of base coat between the flakes. Plan one kit per about 500 sq ft. Read the CCI-610 data sheet for mixing and working time.
    Step 3: the gray tinted CCI-610 epoxy body coat goes on over the primer 3Tinted CCI-610 body coatconcrete slabroll, then cross-rollCCI-610 body coat (tinted)
    CCI-610 tinted gray with XCF #11 Fog. The flakes go into this coat while it is still wet.
  4. Broadcast the flakes while the body coat is wet. Broadcast the XPF flakes by hand onto the wet epoxy until none of the gray body coat shows (a full broadcast). Plan about one 25-lb box per 200 sq ft.
    Step 4: flakes are broadcast by hand onto the wet body coat 4Broadcast the flakesconcrete slabbroadcast flakesby hand, full coverXPF flakes
    Full broadcast: keep adding flakes until the body coat no longer shows.
  5. Scrape, vacuum, top coat. When the body coat has cured, scrape off loose flakes, vacuum, and dip and roll the CCO-651 top coat. This gives the standard textured gloss.
    Step 5: loose flakes are scraped off and the clear CCO-651 top coat is rolled on 5CCO-651 top coatconcrete slabscrape loose flakes,vacuum, then top coatCCO-651 top coat
    One CCO-651 coat seals the flakes and keeps their texture.
  6. Optional: smooth gloss or matte. For a smoother floor, add UPS-670 (gloss) or UPS-675 (matte) after the CCO-651 is dry. It does not replace the CCO-651. UPS-675 mixing, per STAUF: combine A and B, mix 3 minutes, let it rest 15 minutes, mix 1 more minute, then dip and roll.
    Step 6: an optional UPS-670 gloss or UPS-675 matte coat goes on top of the CCO-651 6Optional UPS coatconcrete slabroll, then cross-rollUPS-670 / UPS-675
    UPS-670 = smooth gloss, UPS-675 = smooth matte. Goes on after the CCO-651 is dry.

All of these STAUF coatings are two-part products. Read each data sheet for mixing, working time, and temperature and humidity limits before you start.

The layers, from the floor up

Cross-section of a STAUF garage flake floor: concrete, EHS-265 primer, tinted CCI-610, XPF flakes, CCO-651, optional UPS coat top (you walk here)UPS-670 / UPS-675 (optional)CCO-651 top coatXPF flakes, full broadcastCCI-610, tinted #11 FogEHS-265 primerConcrete slab, groundbottom
STAUF's garage system, per Wolfgang Stauf: 265, 610 and 651.

Commercial kitchen? Swap the body coat

For a commercial kitchen on concrete, STAUF uses the same steps with one product swap: the body coat is ULC-500 LevelSeal instead of CCI-610 epoxy. As on every STAUF flake floor, a UPS-670 or UPS-675 coat over the CCO-651 is optional.

  1. Prep and prime with EHS-265, as above.
  2. Spread ULC-500 with the #10 trowel blade and backroll with the blue texture roller to release bubbles. ULC-500 is tan, so under gray flakes tint each kit with one 2 fl oz bottle of XCF #11 Fog (STAUF: the 2 oz tints are only for ULC-500). One kit covers about 100 sq ft.
  3. Broadcast the flakes into the wet ULC-500.
  4. Scrape, vacuum and top coat with CCO-651.
  5. Optional: for a smoother finish, add UPS-670 (gloss) or UPS-675 (matte). One CCO-651 coat already gives a shiny, textured floor (STAUF).
Kitchen branch: tinted ULC-500 body coat spread with a notched trowel over the primer 2Kitchen: ULC-500 body coatconcrete slabnotched trowelULC-500 body coat (tinted)
In a kitchen the body coat is ULC-500 LevelSeal, tinted with a 2 fl oz XCF bottle per kit.

In the calculator, pick "Kitchen" to get the kitchen layer list. Kitchen over existing tile, or a bathroom? Those go over tile with STAUF's tile system: see epoxy over existing tile.

Moisture in the slab

Hawaii slabs can carry moisture. STAUF's moisture vapor barrier is ERP-270 Perma-Seal: its guide says it protects an epoxy floor from 25 lb or 100% RH. On a damp slab the order is: EHS-265 primer first (STAUF: 265 is always the first coat over concrete, even when you use 270), then ERP-270 as the moisture barrier, then the body coat. If you suspect a moisture problem, call or text us at (808) 210-4807 before you buy, and we'll check your slab with STAUF.

What a 400 sq ft garage needs

These are the quantities our epoxy floor calculator plans for 400 sq ft of bare concrete with a textured gloss finish, at our prices on 20 Nov 2026. We add about 10% extra, as STAUF recommends, then round each product up to whole kits.

Product Qty Total
EHS-265 Hydro-Seal primer, 2.5-gal kit (800 sq ft per kit) 1 $342.42
CCI-610 Summit body coat, 2.5-gal kit (500 sq ft per kit) 1 $374.02
XCF #11 Fog tint, 32 fl oz (1 per CCI-610 kit) 1 $55.00
XPF flakes, 25-lb box (200 sq ft per box) 3 $441.42
CCO-651 top coat, 2-gal kit (480 sq ft per kit) 1 $660.00
Subtotal $1,872.86
Hawaii GET 4.712% $88.25
Total $1,961.11

EFP-290 for repairs and a UPS-670 or UPS-675 finish coat are extra, if you need them. Prices change. The calculator always uses today's prices, and you can send the result to us for a confirmed quote.

Which STAUF product goes where

Follow each floor in order, 1 to 7: that is the order you apply them. Same color = same product.

1Patch
2Primer
3Body / color coat
4Tint
5Decoration
6Top coat
7Final coat
Garageconcrete
1 PatchEFP-290Epoxy floor patchcracks, holes, spalls
2 PrimerEHS-265Epoxy primer800 sq ft / kit
3 Body / color coatCCI-610Epoxy body coat500 sq ft / kit
4 TintXCF #11 FogGray tint32 oz per CCI kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Commercial kitchenconcrete
1 PatchEFP-290Epoxy floor patchcracks, holes, spalls
2 PrimerEHS-265Epoxy primer800 sq ft / kit
3 Body / color coatULC-500LevelSeal body coat100 sq ft / kit
4 TintXCF #11 FogGray tint2 oz per ULC kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Bathroom / any tileexisting tile
1 PatchEFP-290Epoxy floor patchbroken tiles
2 PrimerERP-270 + sandPrimer + moisture barrier175 sq ft / kit
3 Body / color coatULC-500LevelSeal body coat100 sq ft / kit
4 TintXCF #11 FogGray tint2 oz per ULC kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Plywoodbare subfloor
1 PatchEFP-290Epoxy floor patchscrew holes, seams
2 PrimerEHS-265 × 2Epoxy primer, 2 coats800 sq ft / kit per coat
3 Body / color coatULC-500LevelSeal body coat100 sq ft / kit
4 TintXCF #11 FogGray tint2 oz per ULC kit
5 DecorationXPFFlakes, full cover200 sq ft / box
6 Top coatCCO-651Polyurethane top coat480 sq ft / kit
7 Final coatUPS-670 / 675*Gloss / matte sealerup to 400 sq ft/gal
Metallicconcrete
1 PatchEFP-290Epoxy floor patchcracks, holes, spalls
2 PrimerEHS-265Epoxy primer800 sq ft / kit
3 Body / color coatERP-270Base coat, #10 trowel175 sq ft / kit
4 TintXCF Jet (black), 32 ozBase tint, special order (STAUF 1st choice)1 per ERP kit
5 DecorationCCI-610 + pigmentMetallic coat (pigment: special order)125 sq ft / kit + 12 oz pigment per kit
6 Top coatno flakes,
no CCO-651
7 Final coatUPS-670 / 675Gloss / matte, the only top coatup to 400 sq ft/gal
  1. 1Tile → ERP-270 primer. Everything else → EHS-265.
  2. 2Rigid concrete garage → CCI-610 body coat. Anything that moves, or a kitchen (tile, plywood, kitchen slab) → ULC-500.
  3. 3Every flake floor → XPF flakes + CCO-651.
  4. 4UPS-670 / UPS-675 = optional last coat on flake floors, for a smoother finish. On metallic it is the only top coat.

* Flake floors: UPS-670/675 is optional. STAUF (20 Nov 2026): one CCO-651 coat gives a shiny, textured floor; add UPS for a smoother finish. Coverage is approximate, per kit or box, before the ~10% extra our calculator adds. EFP-290: as much as the repairs need. Kit sizes: EHS-265, ERP-270, CCI-610 2.5 gal; CCO-651 2 gal; XPF 25-lb box. Sources: STAUF USA (system recipes, coatings director's rates), STAUF data sheets and the DCS metallic guide. Best Flooring Honolulu, 20 Nov 2026.

The rest of the series

Where to get the materials on Oahu

Best Flooring Honolulu is STAUF's exclusive distributor in Hawaii. Pick up the STAUF flake-floor products at our Waipio warehouse, or we ship to all islands. See every STAUF product and the epoxy flooring collection. Call or text (808) 210-4807.

FAQ: how to epoxy a garage floor

How do you epoxy a garage floor step by step?

With STAUF's flake system: prep the slab (grind so a water drop soaks in within 60 seconds, patch cracks with EFP-290), roll and cross-roll the EHS-265 primer, apply the CCI-610 body coat tinted with XCF #11 Fog, broadcast XPF flakes into the wet coat, then scrape, vacuum and dip-and-roll the CCO-651 top coat. A UPS-670 gloss or UPS-675 matte coat is optional.

How much epoxy do I need for a 400 sq ft garage?

Our calculator plans 1 EHS-265 kit, 1 CCI-610 2.5-gal kit, one 32 fl oz XCF #11 Fog tint, 3 boxes of XPF flakes and 1 CCO-651 kit for 400 sq ft. That is about $1,961 with Hawaii GET at our 20 Nov 2026 prices.

Do I have to grind the concrete before epoxy?

STAUF's DCS installation guide calls for mechanical preparation: grind off paint, drywall mud and other contaminants until the concrete is porous. Test by sprinkling water drops on a vacuumed area. If they soak in within 60 seconds, the slab is ready.

What is different about epoxy flooring in a commercial kitchen?

STAUF's kitchen system uses the same steps but swaps the CCI-610 epoxy body coat for ULC-500 LevelSeal, tinted with one 2 fl oz XCF #11 Fog bottle per kit. A UPS-670 or UPS-675 coat over the CCO-651 is optional.

How many coats does an epoxy flake floor need?

Four layers: EHS-265 primer, the tinted CCI-610 body coat, a full flake broadcast, and the CCO-651 top coat, plus an optional UPS-670 or UPS-675 coat for a smoother gloss or matte finish.

Sources: STAUF USA coatings team (system, coverage rates, tint sizes, UPS-675 mixing; review of 20 Nov 2026), STAUF DCS installation guide (concrete prep, EHS-265 application, ERP-270 moisture rating), our calculator. Updated 20 Nov 2026.

November 20, 2026 — Best Flooring Honolulu

Leave a comment

Please note: comments must be approved before they are published.